Cudy M1200 v1 OpenWrt Firmware
- CPU
- MediaTek MT7628AN
- RAM
- 128 MB
- Flash
- 16 MB
The Cudy M1200 v1 is supported by OpenWrt on the ramips/mt76x8 target. 2 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | MediaTek MT7628AN |
|---|---|
| CPU cores | 1 |
| CPU frequency | 580 MHz |
| RAM | 128 MB |
| Flash | 16 MB |
| 100 Mbit Ethernet ports | 1 |
| WLAN hardware | MediaTek MT7628AN, MediaTek MT7613BEN |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | ramips/mt76x8 | cudy_m1200-v1 |
Downloads
Download images
OpenWrt 25.12.5 · ramips/mt76x8
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-ramips-mt76x8-cudy_m1200-v1-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | eae7adee0068… |
| openwrt-25.12.5-ramips-mt76x8-cudy_m1200-v1-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | c331defbf825… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Cudy M1200 v1 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (2)
kmod-mt7615e kmod-mt7663-firmware-ap
Target default packages (28)
apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-gpio-button-hotplug kmod-leds-gpio kmod-mt7603 kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe swconfig uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-ramips-mt76x8-cudy_m1200-v1-initramfs-kernel.bin eae7adee0068afa456b022e26a901d270be536da5d738ca78f405c764e99396c openwrt-25.12.5-ramips-mt76x8-cudy_m1200-v1-initramfs-kernel.bin
Build custom firmware
Need more than the default image for the Cudy M1200 v1? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Cudy devices
- Cudy AP1300 Outdoor v1 OpenWrt firmware
- Cudy AP3000 Outdoor v1 OpenWrt firmware
- Cudy AP3000 v1 OpenWrt firmware
- Cudy AP3000 Wall v1 OpenWrt firmware
- Cudy C200P OpenWrt firmware
- Cudy LT300 v3 OpenWrt firmware
- Cudy M1300 v2 OpenWrt firmware
- Cudy M1800 OpenWrt firmware
More devices on ramips/mt76x8
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.