ELECOM WRC-1167FS OpenWrt Firmware
- CPU
- MediaTek MT7628AN
- RAM
- 64 MB
- Flash
- 16 MB
The ELECOM WRC-1167FS is supported by OpenWrt on the ramips/mt76x8 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | MediaTek MT7628AN |
|---|---|
| CPU cores | 1 |
| CPU frequency | 575 MHz |
| RAM | 64 MB |
| Flash | 16 MB |
| 100 Mbit Ethernet ports | 2 |
| WLAN hardware | MediaTek MT7628AN, MediaTek MT7612E |
| Switch | MediaTek MT7628AN |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | ramips/mt76x8 | elecom_wrc-1167fs |
Downloads
Download images
OpenWrt 25.12.5 · ramips/mt76x8
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-ramips-mt76x8-elecom_wrc-1167fs-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 8e1d995bb9bd… |
| openwrt-25.12.5-ramips-mt76x8-elecom_wrc-1167fs-squashfs-factory.bin For first-time flash from stock firmware. | factory | 5315ea78ffa4… |
| openwrt-25.12.5-ramips-mt76x8-elecom_wrc-1167fs-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | d6e7910aea06… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the ELECOM WRC-1167FS ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (1)
kmod-mt76x2
Target default packages (28)
apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-gpio-button-hotplug kmod-leds-gpio kmod-mt7603 kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe swconfig uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-ramips-mt76x8-elecom_wrc-1167fs-squashfs-sysupgrade.bin 8e1d995bb9bd5f86ca9950a5329badf3ab1e609994d754702e61dea26f82a4e5 openwrt-25.12.5-ramips-mt76x8-elecom_wrc-1167fs-squashfs-sysupgrade.bin
Build custom firmware
Need more than the default image for the ELECOM WRC-1167FS? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More ELECOM devices
- ELECOM WAB-I1750-PS OpenWrt firmware
- ELECOM WAB-S1167-PS OpenWrt firmware
- ELECOM WAB-S600-PS OpenWrt firmware
- ELECOM WMC-M1267GST2 OpenWrt firmware
- ELECOM WMC-S1267GS2 OpenWrt firmware
- ELECOM WMC-X1800GST OpenWrt firmware
- ELECOM WRC-1167GHBK2-S OpenWrt firmware
- ELECOM WRC-1167GS2-B OpenWrt firmware
More devices on ramips/mt76x8
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.