NETGEAR DM200 OpenWrt Firmware
- CPU
- Lantiq XWAY VRX220 (PSB 80220 EL)
- RAM
- 64 MB
- Flash
- 8 MB
The NETGEAR DM200 is supported by OpenWrt on the lantiq/xrx200_legacy target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Lantiq XWAY VRX220 (PSB 80220 EL) |
|---|---|
| CPU cores | 2 |
| CPU frequency | 500 MHz |
| RAM | 64 MB |
| Flash | 8 MB |
| 100 Mbit Ethernet ports | 1 |
| Switch | Lantiq GSWIP (built-in SoC switch) |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | lantiq/xrx200_legacy | netgear_dm200 |
Downloads
Download images
OpenWrt 25.12.5 · lantiq/xrx200_legacy
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-lantiq-xrx200_legacy-netgear_dm200-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 7daad2d633c0… |
| openwrt-25.12.5-lantiq-xrx200_legacy-netgear_dm200-squashfs-factory.img For first-time flash from stock firmware. | factory | 710fa30c9441… |
| openwrt-25.12.5-lantiq-xrx200_legacy-netgear_dm200-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | 0e6073ea0be2… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the NETGEAR DM200 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (2)
xrx200-rev1.1-phy22f-firmware xrx200-rev1.2-phy22f-firmware
Target default packages (36)
apk-mbedtls base-files ca-bundle dnsmasq dropbear dsl-vrx200-firmware-xdsl-a dsl-vrx200-firmware-xdsl-b-patch firewall4 fstools kmod-dsa-gswip kmod-gpio-button-hotplug kmod-leds-gpio kmod-ltq-atm-vr9 kmod-ltq-deu-vr9 kmod-ltq-ptm-vr9 kmod-ltq-vdsl-vr9 kmod-ltq-vdsl-vr9-mei kmod-nft-offload libc libgcc libustream-mbedtls logd ltq-vdsl-vr9-app ltq-vdsl-vr9-vectoring-fw-installer mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoa ppp-mod-pppoe uci uclient-fetch urandom-seed urngd
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-lantiq-xrx200_legacy-netgear_dm200-squashfs-sysupgrade.bin 7daad2d633c065bc64895989753cba49109a790a04b2c2c9fcf1349468ec8493 openwrt-25.12.5-lantiq-xrx200_legacy-netgear_dm200-squashfs-sysupgrade.bin
Build custom firmware
Need more than the default image for the NETGEAR DM200? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More NETGEAR devices
- NETGEAR Centria N900 WNDR4700 OpenWrt firmware
- NETGEAR DGN3500 OpenWrt firmware
- NETGEAR DGN3500B OpenWrt firmware
- NETGEAR DGND3700 v1 OpenWrt firmware
- NETGEAR DGND3700 v2 OpenWrt firmware
- NETGEAR DGND3800B OpenWrt firmware
- NETGEAR EAX12 OpenWrt firmware
- NETGEAR EAX17 OpenWrt firmware
More devices on lantiq/xrx200_legacy
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.