D-Link DGS-1210-26 OpenWrt Firmware
- CPU
- Realtek RTL8382M
- RAM
- 128 MB
- Flash
- 32 MB
The D-Link DGS-1210-26 is supported by OpenWrt on the realtek/rtl838x target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Realtek RTL8382M |
|---|---|
| CPU cores | 1 |
| CPU frequency | 500 MHz |
| RAM | 128 MB |
| Flash | 32 MB |
| 1 Gbit Ethernet ports | more than 20 |
| Switch | Realtek RTL8382M |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | realtek/rtl838x | d-link_dgs-1210-26 |
Downloads
Download images
OpenWrt 25.12.5 · realtek/rtl838x
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-realtek-rtl838x-d-link_dgs-1210-26-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 7541971c87e6… |
| openwrt-25.12.5-realtek-rtl838x-d-link_dgs-1210-26-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | d04ccbab129d… |
| openwrt-25.12.5-realtek-rtl838x-d-link_dgs-1210-26-squashfs-factory_image1.bin For first-time flash from stock firmware. | factory_image1 | d8ead0c1d3f3… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the D-Link DGS-1210-26 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Target default packages (21)
apk-mbedtls base-files ca-bundle dropbear ethtool firewall4 fstools kmod-gpio-button-hotplug libc libgcc libustream-mbedtls logd mtd netifd odhcp6c procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-realtek-rtl838x-d-link_dgs-1210-26-squashfs-sysupgrade.bin 7541971c87e6767c142b40c6cf65e2785b7ff84424a2535bbcc3237a57af036b openwrt-25.12.5-realtek-rtl838x-d-link_dgs-1210-26-squashfs-sysupgrade.bin
Build custom firmware
Need more than the default image for the D-Link DGS-1210-26? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More D-Link devices
- D-Link AQUILA PRO AI E30 A1 OpenWrt firmware
- D-Link AQUILA PRO AI M30 A1 OpenWrt firmware
- D-Link AQUILA PRO AI M60 A1 OpenWrt firmware
- D-Link COVR-C1200 A1 OpenWrt firmware
- D-Link COVR-P2500 A1 OpenWrt firmware
- D-Link COVR-X1860 A1 OpenWrt firmware
- D-Link DAP-1325 A1 OpenWrt firmware
- D-Link DAP-1330 A1 OpenWrt firmware
More devices on realtek/rtl838x
- ALLNET ALL-SG8208M OpenWrt firmware
- APRESIA ApresiaLightGS120GT-SS OpenWrt firmware
- EnGenius EWS2910P v1 OpenWrt firmware
- EnGenius EWS2910P v3 OpenWrt firmware
- HPE 1920-16G (JG923A) OpenWrt firmware
- HPE 1920-24G (JG924A) OpenWrt firmware
- HPE 1920-24G-PoE+ 180W (JG925A) OpenWrt firmware
- HPE 1920-24G-PoE+ 370W (JG926A) OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.