Elecom WRH-300CR OpenWrt Firmware
- CPU
- MediaTek MT7620N
- RAM
- 64 MB
- Flash
- 16, SD, microSD MB
The Elecom WRH-300CR is supported by OpenWrt on the ramips/mt7620 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | MediaTek MT7620N |
|---|---|
| CPU cores | 1 |
| CPU frequency | 580 MHz |
| RAM | 64 MB |
| Flash | 16, SD, microSD MB |
| 100 Mbit Ethernet ports | 1 |
| WLAN hardware | MediaTek MT7620N |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | ramips/mt7620 | elecom_wrh-300cr |
Downloads
Download images
OpenWrt 25.12.5 · ramips/mt7620
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-ramips-mt7620-elecom_wrh-300cr-squashfs-factory.bin For first-time flash from stock firmware. | factory | 4c2627cfa0f2… |
| openwrt-25.12.5-ramips-mt7620-elecom_wrh-300cr-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | 8abd51935c6f… |
| openwrt-25.12.5-ramips-mt7620-elecom_wrh-300cr-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | ecdb9cd3d292… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Elecom WRH-300CR ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (2)
kmod-usb2 kmod-usb-ohci
Target default packages (29)
apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-rt2800-soc libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail swconfig uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-ramips-mt7620-elecom_wrh-300cr-squashfs-factory.bin 4c2627cfa0f281b83a10b1eb6df8017ecdcf5f910c53c2b817a095732cfd1ea0 openwrt-25.12.5-ramips-mt7620-elecom_wrh-300cr-squashfs-factory.bin
Build custom firmware
Need more than the default image for the Elecom WRH-300CR? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Elecom devices
More devices on ramips/mt7620
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.