NETGEAR WNDAP660 (Dual Radio Dual Band Wireless-N) OpenWrt Firmware

The NETGEAR WNDAP660 (Dual Radio Dual Band Wireless-N) is supported by OpenWrt/ImmortalWrt on the apm821xx/nand target. 6 firmware images are available from the official OpenWrt 25.12.5 and ImmortalWrt 25.12.1 stable releases — download one below, or build a custom OpenWrt image for this device with your own package selection.

Build matrix

Supported firmware versions

DistributionVersionTargetProfile
OpenWrt25.12.5apm821xx/nandnetgear_wndap660
ImmortalWrt25.12.1apm821xx/nandnetgear_wndap660

Downloads

Download images

OpenWrt 25.12.5 · apm821xx/nand

ImageTypesha256
openwrt-25.12.5-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kernel517757eeeb2b
openwrt-25.12.5-apm821xx-nand-netgear_wndap660-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade59b2150d8a83
openwrt-25.12.5-apm821xx-nand-netgear_wndap660-squashfs-factory.img

For first-time flash from stock firmware.

factorya4210cce2a27

ImmortalWrt 25.12.1 · apm821xx/nand

ImageTypesha256
immortalwrt-25.12.1-apm821xx-nand-netgear_wndap660-squashfs-factory.img

For first-time flash from stock firmware.

factory137ec6618d7b
immortalwrt-25.12.1-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kernel9069ea2cbd44
immortalwrt-25.12.1-apm821xx-nand-netgear_wndap660-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgradede4cb09d3a16

Downloads are served by the official OpenWrt/ImmortalWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the NETGEAR WNDAP660 (Dual Radio Dual Band Wireless-N) ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

OpenWrt 25.12.5 · apm821xx/nand

Device packages (1)

kmod-eeprom-at24

Target default packages (32)

apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-hw-crypto-4xx kmod-i2c-core kmod-leds-gpio kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls

ImmortalWrt 25.12.1 · apm821xx/nand

Device packages (1)

kmod-eeprom-at24

Target default packages (36)

apk-openssl base-files block-mount ca-bundle default-settings-chn dnsmasq-full dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-hw-crypto-4xx kmod-i2c-core kmod-leds-gpio kmod-nf-nathelper kmod-nft-offload libc libgcc libustream-openssl logd luci mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-openssl

Installation notes

  • First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
  • Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
  • The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
  • Verify your download against the published checksum before flashing:
    $ sha256sum openwrt-25.12.5-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    517757eeeb2b9c425ba049c4ccf85f21dfd2deaa9b170f65e7ff8d33ad950198  openwrt-25.12.5-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin

Build custom firmware

Need more than the default image for the NETGEAR WNDAP660 (Dual Radio Dual Band Wireless-N)? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device