SolidRun ClearFog Base OpenWrt Firmware
- CPU
- Marvell Armada 388 88F6828
- RAM
- 1024 MB
- Flash
- microSD
The SolidRun ClearFog Base is supported by OpenWrt on the mvebu/cortexa9 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Marvell Armada 388 88F6828 |
|---|---|
| CPU cores | 2 |
| CPU frequency | 1600 MHz |
| RAM | 1024 MB |
| Flash | microSD |
| 1 Gbit Ethernet ports | 2 |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | mvebu/cortexa9 | solidrun_clearfog-base-a1 |
Downloads
Download images
OpenWrt 25.12.5 · mvebu/cortexa9
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-mvebu-cortexa9-solidrun_clearfog-base-a1-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | f6a71681bcc6… |
| openwrt-25.12.5-mvebu-cortexa9-solidrun_clearfog-base-a1-targz-rootfs.tar.gz Rootfs archive for Docker / LXC containers. | rootfs | feafa7aeb05e… |
| openwrt-25.12.5-mvebu-cortexa9-solidrun_clearfog-base-a1-squashfs-sdcard.img.gz Disk image to write onto an SD card. | sdcard | ce40157dfd3c… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the SolidRun ClearFog Base ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (4)
mkf2fs e2fsprogs partx-utils kmod-dsa-mv88e6xxx
Target default packages (26)
apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-gpio-button-hotplug kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd
Installation notes
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-mvebu-cortexa9-solidrun_clearfog-base-a1-initramfs-kernel.bin f6a71681bcc6857766d2b61bfa82baff745ac8a281448a745947c0f3bc1182ef openwrt-25.12.5-mvebu-cortexa9-solidrun_clearfog-base-a1-initramfs-kernel.bin
Build custom firmware
Need more than the default image for the SolidRun ClearFog Base? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More SolidRun devices
- SolidRun Clearfog GT-8K OpenWrt firmware
- SolidRun ClearFog Pro OpenWrt firmware
- SolidRun CuBox-i OpenWrt firmware
- SolidRun MACCHIATObin Double Shot OpenWrt firmware
- SolidRun MACCHIATObin Single Shot OpenWrt firmware
More devices on mvebu/cortexa9
- Buffalo LinkStation LS220DE OpenWrt firmware
- Buffalo LinkStation LS421DE OpenWrt firmware
- Ctera C200 V2 OpenWrt firmware
- CZ.NIC Turris Omnia OpenWrt firmware
- Fortinet FortiGate 30E OpenWrt firmware
- Fortinet FortiGate 50E OpenWrt firmware
- Fortinet FortiGate 51E OpenWrt firmware
- Fortinet FortiGate 52E OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.