Cisco Meraki MR30H OpenWrt Firmware

The Cisco Meraki MR30H is supported by OpenWrt/ImmortalWrt on the ipq40xx/generic target. 4 firmware images are available from the official OpenWrt 25.12.5 and ImmortalWrt 25.12.1 stable releases — download one below, or build a custom OpenWrt image for this device with your own package selection.

Build matrix

Supported firmware versions

DistributionVersionTargetProfile
OpenWrt25.12.5ipq40xx/genericmeraki_mr30h
ImmortalWrt25.12.1ipq40xx/genericmeraki_mr30h

Downloads

Download images

OpenWrt 25.12.5 · ipq40xx/generic

ImageTypesha256
openwrt-25.12.5-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgradea0a73c48f57d…
openwrt-25.12.5-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb

Minimal kernel image, useful for first install or recovery.

kernel07d97f411ac7…

ImmortalWrt 25.12.1 · ipq40xx/generic

ImageTypesha256
immortalwrt-25.12.1-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade87a72153789b…
immortalwrt-25.12.1-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb

Minimal kernel image, useful for first install or recovery.

kernel5505e5cc4209…

Downloads are served by the official OpenWrt/ImmortalWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the Cisco Meraki MR30H ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

OpenWrt 25.12.5 · ipq40xx/generic

Device packages (2)

ath10k-firmware-qca9887-ct ipq-wifi-meraki_mr30h

Target default packages (34)

apk-mbedtls ath10k-board-qca4019 ath10k-firmware-qca4019-ct base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-ath10k-ct kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls

ImmortalWrt 25.12.1 · ipq40xx/generic

Device packages (2)

ath10k-firmware-qca9887-ct ipq-wifi-meraki_mr30h

Target default packages (41)

apk-openssl ath10k-board-qca4019 ath10k-firmware-qca4019-ct autocore automount base-files block-mount ca-bundle default-settings-chn dnsmasq-full dropbear firewall4 fstools kmod-ath10k-ct kmod-gpio-button-hotplug kmod-leds-gpio kmod-nf-nathelper kmod-nft-offload kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-openssl logd luci luci-app-cpufreq mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-openssl

Installation notes

  • Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
  • The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
  • Verify your download against the published checksum before flashing:
    $ sha256sum openwrt-25.12.5-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin
a0a73c48f57d5cef1ac77425a87d15919e8e94add39cdb42ecfaa9f9376bd1d4  openwrt-25.12.5-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin

Build custom firmware

Need more than the default image for the Cisco Meraki MR30H? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device

Related

Related devices

More Cisco Meraki devices

More devices on ipq40xx/generic

Upstream

Upstream & source

Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.