CMCC RM2-6 OpenWrt Firmware
- CPU
- Qualcomm IPQ8070A
- RAM
- 512 MB
- Flash
- 256NAND MB
The CMCC RM2-6 is supported by OpenWrt on the qualcommax/ipq807x target. 4 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Qualcomm IPQ8070A |
|---|---|
| CPU cores | 4 |
| CPU frequency | 1000 MHz |
| RAM | 512 MB |
| Flash | 256NAND MB |
| 1 Gbit Ethernet ports | 2 |
| WLAN hardware | Qualcomm QCN5024, Qualcomm QCN5054 |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | qualcommax/ipq807x | cmcc_rm2-6 |
Downloads
Download images
OpenWrt 25.12.5 · qualcommax/ipq807x
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-initramfs-uImage.itb Minimal kernel image, useful for first install or recovery. | kernel | ce04cb810d04… |
| openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 635d9b392b3c… |
| openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-squashfs-factory.bin For first-time flash from stock firmware. | factory | 05a9d46f6d43… |
| openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-squashfs-factory.ubi For first-time flash from stock firmware. | factory | 47decce57f8b… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the CMCC RM2-6 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (2)
ipq-wifi-cmcc_rm2-6 kmod-hwmon-gpiofan
Target default packages (38)
apk-mbedtls ath11k-firmware-ipq8074 base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-ath11k-ahb kmod-fs-ext4 kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-phy-aquantia kmod-qca-nss-dp kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-mbedtls logd losetup mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-initramfs-uImage.itb ce04cb810d043361b55c0bffcc86d8df19f3d8a5ddf3daebadd24c769ca309e1 openwrt-25.12.5-qualcommax-ipq807x-cmcc_rm2-6-initramfs-uImage.itb
Build custom firmware
Need more than the default image for the CMCC RM2-6? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More CMCC devices
- CMCC A10 (OpenWrt U-Boot layout) OpenWrt firmware
- CMCC A10 (stock layout) OpenWrt firmware
- CMCC PZ-L8 OpenWrt firmware
- CMCC RAX3000M OpenWrt firmware
More devices on qualcommax/ipq807x
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.