Edgecore EAP102 OpenWrt Firmware
- CPU
- Qualcomm IPQ8070A
- RAM
- 1024 MB
- Flash
- 32, 256NAND MB
The Edgecore EAP102 is supported by OpenWrt on the qualcommax/ipq807x target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Qualcomm IPQ8070A |
|---|---|
| CPU cores | 4 |
| CPU frequency | 1400 MHz |
| RAM | 1024 MB |
| Flash | 32, 256NAND MB |
| 2.5 Gbit Ethernet ports | 2 |
| WLAN hardware | Qualcomm QCN5124, Qualcomm QCN5154 |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | qualcommax/ipq807x | edgecore_eap102 |
Downloads
Download images
OpenWrt 25.12.5 · qualcommax/ipq807x
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-qualcommax-ipq807x-edgecore_eap102-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 8860bcbf58bc… |
| openwrt-25.12.5-qualcommax-ipq807x-edgecore_eap102-squashfs-factory.ubi For first-time flash from stock firmware. | factory | 8af77ed0d06c… |
| openwrt-25.12.5-qualcommax-ipq807x-edgecore_eap102-initramfs-uImage.itb Minimal kernel image, useful for first install or recovery. | kernel | 0927b82d8df5… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Edgecore EAP102 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (1)
ipq-wifi-edgecore_eap102
Target default packages (38)
apk-mbedtls ath11k-firmware-ipq8074 base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-ath11k-ahb kmod-fs-ext4 kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-phy-aquantia kmod-qca-nss-dp kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-mbedtls logd losetup mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-qualcommax-ipq807x-edgecore_eap102-squashfs-sysupgrade.bin 8860bcbf58bc0eafc47dabb06cfa74f8d7460f8968bad830301c45241ee5e200 openwrt-25.12.5-qualcommax-ipq807x-edgecore_eap102-squashfs-sysupgrade.bin
Build custom firmware
Need more than the default image for the Edgecore EAP102? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Edgecore devices
More devices on qualcommax/ipq807x
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.