Edgecore EAP111 OpenWrt Firmware
- CPU
- MediaTek MT7981A
- RAM
- 512 MB
- Flash
- 256NAND MB
The Edgecore EAP111 is supported by OpenWrt on the mediatek/filogic target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | MediaTek MT7981A |
|---|---|
| CPU cores | 2 |
| CPU frequency | 1300 MHz |
| RAM | 512 MB |
| Flash | 256NAND MB |
| 1 Gbit Ethernet ports | 2 |
| WLAN hardware | MediaTek MT7981A, MediaTek MT7976CN |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | mediatek/filogic | edgecore_eap111 |
Downloads
Download images
OpenWrt 25.12.5 · mediatek/filogic
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-mediatek-filogic-edgecore_eap111-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | 328d7cb5de84… |
| openwrt-25.12.5-mediatek-filogic-edgecore_eap111-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 5783498288f2… |
| openwrt-25.12.5-mediatek-filogic-edgecore_eap111-squashfs-factory.bin For first-time flash from stock firmware. | factory | 528908e78cd9… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Edgecore EAP111 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (3)
kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
Target default packages (30)
apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fitblk fstools kmod-crypto-hw-safexcel kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-mediatek-filogic-edgecore_eap111-initramfs-kernel.bin 328d7cb5de84a57ad782738588ed2020a5648d06240fc074fc4751331284468b openwrt-25.12.5-mediatek-filogic-edgecore_eap111-initramfs-kernel.bin
Build custom firmware
Need more than the default image for the Edgecore EAP111? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Edgecore devices
More devices on mediatek/filogic
- ABT ASR3000 OpenWrt firmware
- Acelink EW-7886CAX OpenWrt firmware
- Acer Connect Vero W6m OpenWrt firmware
- Acer Predator Connect W6 OpenWrt firmware
- Acer Predator Connect W6d OpenWrt firmware
- Acer Predator Connect W6x (OpenWrt U-Boot Layout) OpenWrt firmware
- Acer Predator Connect W6x (Stock Layout) OpenWrt firmware
- Adtran SDG-8612 OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.