FriendlyARM NanoPi M1 Plus OpenWrt Firmware
- CPU
- Allwinner H3
- RAM
- 1024 MB
- Flash
- eMMC
The FriendlyARM NanoPi M1 Plus is supported by OpenWrt on the sunxi/cortexa7 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Allwinner H3 |
|---|---|
| CPU cores | 4 |
| CPU frequency | 1200 MHz |
| RAM | 1024 MB |
| Flash | eMMC |
| 1 Gbit Ethernet ports | 1 |
| WLAN hardware | AMPAK AP6212A (Broadcom BCM43430) |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | sunxi/cortexa7 | friendlyarm_nanopi-m1-plus |
Downloads
Download images
OpenWrt 25.12.5 · sunxi/cortexa7
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-sunxi-cortexa7-friendlyarm_nanopi-m1-plus-ext4-sdcard.img.gz Disk image to write onto an SD card. | sdcard | 68fb0f5c0efd… |
| openwrt-25.12.5-sunxi-cortexa7-friendlyarm_nanopi-m1-plus-squashfs-sdcard.img.gz Disk image to write onto an SD card. | sdcard | eb3839e84ed1… |
| openwrt-25.12.5-sunxi-cortexa7-friendlyarm_nanopi-m1-plus-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | dc7ebdec4567… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the FriendlyARM NanoPi M1 Plus ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (4)
kmod-leds-gpio kmod-brcmfmac cypress-firmware-43430-sdio wpad-basic-mbedtls
Target default packages (28)
apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-nft-offload libc libgcc libustream-mbedtls logd mkf2fs mtd netifd nftables odhcp6c odhcpd-ipv6only partx-utils ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd
Installation notes
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-sunxi-cortexa7-friendlyarm_nanopi-m1-plus-ext4-sdcard.img.gz 68fb0f5c0efdb08b449890b5f57cafbfe7034bc346957790017934c823ed7133 openwrt-25.12.5-sunxi-cortexa7-friendlyarm_nanopi-m1-plus-ext4-sdcard.img.gz
Build custom firmware
Need more than the default image for the FriendlyARM NanoPi M1 Plus? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More FriendlyARM devices
- FriendlyARM NanoPC T4 OpenWrt firmware
- FriendlyARM NanoPC T6 OpenWrt firmware
- FriendlyARM NanoPi NEO OpenWrt firmware
- FriendlyARM NanoPi NEO Air OpenWrt firmware
- FriendlyARM NanoPi NEO Plus2 OpenWrt firmware
- FriendlyARM NanoPi NEO2 OpenWrt firmware
- FriendlyARM NanoPi R1 OpenWrt firmware
- FriendlyARM Nanopi R1S H5 OpenWrt firmware
More devices on sunxi/cortexa7
- Cubietech Cubieboard2 OpenWrt firmware
- Cubietech Cubietruck OpenWrt firmware
- Lamobo Lamobo R1 OpenWrt firmware
- LeMaker Banana Pi OpenWrt firmware
- LeMaker Banana Pro OpenWrt firmware
- LicheePi Zero with Dock (V3s) OpenWrt firmware
- LinkSprite pcDuino3 OpenWrt firmware
- LinkSprite pcDuino3 Nano OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.