FriendlyARM NanoPi NEO Plus2 OpenWrt Firmware
- CPU
- Allwinner H5
- RAM
- 1024 MB
- Flash
- 8192NAND, microSD MB
The FriendlyARM NanoPi NEO Plus2 is supported by OpenWrt on the sunxi/cortexa53 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Allwinner H5 |
|---|---|
| CPU cores | 4 |
| CPU frequency | 1200 MHz |
| RAM | 1024 MB |
| Flash | 8192NAND, microSD MB |
| 1 Gbit Ethernet ports | 1 |
| WLAN hardware | AMPAK AP6212A (Broadcom BCM43430) |
| Switch | Realtek RTL8211E Phy |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | sunxi/cortexa53 | friendlyarm_nanopi-neo-plus2 |
Downloads
Download images
OpenWrt 25.12.5 · sunxi/cortexa53
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-sunxi-cortexa53-friendlyarm_nanopi-neo-plus2-ext4-sdcard.img.gz Disk image to write onto an SD card. | sdcard | df02cff3516d… |
| openwrt-25.12.5-sunxi-cortexa53-friendlyarm_nanopi-neo-plus2-squashfs-sdcard.img.gz Disk image to write onto an SD card. | sdcard | d53366b6eca1… |
| openwrt-25.12.5-sunxi-cortexa53-friendlyarm_nanopi-neo-plus2-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | ed7fda353e14… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the FriendlyARM NanoPi NEO Plus2 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Target default packages (28)
apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-nft-offload libc libgcc libustream-mbedtls logd mkf2fs mtd netifd nftables odhcp6c odhcpd-ipv6only partx-utils ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd
Installation notes
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-sunxi-cortexa53-friendlyarm_nanopi-neo-plus2-ext4-sdcard.img.gz df02cff3516dc5724de3edb88b53afe4f96bdd5bcb86fbb39102b60df061ea6e openwrt-25.12.5-sunxi-cortexa53-friendlyarm_nanopi-neo-plus2-ext4-sdcard.img.gz
Build custom firmware
Need more than the default image for the FriendlyARM NanoPi NEO Plus2? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More FriendlyARM devices
- FriendlyARM NanoPC T4 OpenWrt firmware
- FriendlyARM NanoPC T6 OpenWrt firmware
- FriendlyARM NanoPi M1 Plus OpenWrt firmware
- FriendlyARM NanoPi NEO OpenWrt firmware
- FriendlyARM NanoPi NEO Air OpenWrt firmware
- FriendlyARM NanoPi NEO2 OpenWrt firmware
- FriendlyARM NanoPi R1 OpenWrt firmware
- FriendlyARM Nanopi R1S H5 OpenWrt firmware
More devices on sunxi/cortexa53
- Libre Computer ALL-H3-CC H5 OpenWrt firmware
- Olimex A64-Olinuxino OpenWrt firmware
- Olimex A64-Olinuxino eMMC OpenWrt firmware
- Pine64 Pine64+ OpenWrt firmware
- Pine64 SoPine OpenWrt firmware
- Xunlong Orange Pi One Plus OpenWrt firmware
- Xunlong Orange Pi PC 2 OpenWrt firmware
- Xunlong Orange Pi Zero 2 OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.