GL.iNet GL-MT6000 OpenWrt Firmware

Name: GL.iNet GL-MT6000
Brand: GL.iNet

The GL.iNet GL-MT6000 is supported by OpenWrt on the mediatek/filogic target. 5 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.

Build matrix

Supported firmware versions

Distribution	Version	Target	Profile
OpenWrt	25.12.5	mediatek/filogic	glinet_gl-mt6000

Downloads

Download images

OpenWrt 25.12.5 · mediatek/filogic

Image	Type	sha256
openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery.	kernel	d4a86e33260f…
openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip	bl31-uboot.fip	ff8b11cfc0fe…
openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt.	sysupgrade	4b506982cc4a…
openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-preloader.bin	preloader.bin	d1f272a3a5d4…
openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin For first-time flash from stock firmware.	factory	d0c997128c3c…

Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the GL.iNet GL-MT6000 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

Device packages (7)

e2fsprogs f2fsck mkf2fs kmod-usb3 kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware

Target default packages (30)

apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fitblk fstools kmod-crypto-hw-safexcel kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls

Installation notes

First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.

Verify your download against the published checksum before flashing:

$ sha256sum openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-initramfs-kernel.bin
d4a86e33260f6fc3e4950438647455e7675e5c6f74fc7e00025255674f8c1a39  openwrt-25.12.5-mediatek-filogic-glinet_gl-mt6000-initramfs-kernel.bin

Build custom firmware

Need more than the default image for the GL.iNet GL-MT6000? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device

More GL.iNet devices

More devices on mediatek/filogic

Upstream

Upstream & source

Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.