Sitecom WLR-7100 OpenWrt Firmware

CPU
Atheros AR1022
RAM
64 MB
Flash
8 MB

The Sitecom WLR-7100 is supported by OpenWrt/ImmortalWrt on the ath79/tiny target. 4 firmware images are available from the official OpenWrt 25.12.5 and ImmortalWrt 25.12.1 stable releases — download one below, or build a custom OpenWrt image for this device with your own package selection.

Specs

Specifications

CPUAtheros AR1022
CPU cores1
CPU frequency535 MHz
RAM64 MB
Flash8 MB
1 Gbit Ethernet ports5
WLAN hardwareAtheros AR1022, Qualcomm Atheros QCA9882
SwitchQualcomm Atheros QCA8337N

Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.

Build matrix

Supported firmware versions

DistributionVersionTargetProfile
OpenWrt25.12.5ath79/tinysitecom_wlr-7100
ImmortalWrt25.12.1ath79/tinysitecom_wlr-7100

Downloads

Download images

OpenWrt 25.12.5 · ath79/tiny

ImageTypesha256
openwrt-25.12.5-ath79-tiny-sitecom_wlr-7100-squashfs-factory.dlf

For first-time flash from stock firmware.

factory050dca3674af
openwrt-25.12.5-ath79-tiny-sitecom_wlr-7100-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade5f0ba2547d15
openwrt-25.12.5-ath79-tiny-sitecom_wlr-7100-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kernel46690507090d

ImmortalWrt 25.12.1 · ath79/tiny

ImageTypesha256
immortalwrt-25.12.1-ath79-tiny-sitecom_wlr-7100-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kernel25b0ba9dfab0

Downloads are served by the official OpenWrt/ImmortalWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the Sitecom WLR-7100 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

OpenWrt 25.12.5 · ath79/tiny

Device packages (3)

ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2

Target default packages (28)

apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls

ImmortalWrt 25.12.1 · ath79/tiny

Device packages (3)

ath10k-firmware-qca988x-ct kmod-ath10k-ct-smallbuffers kmod-usb2

Target default packages (32)

apk-openssl base-files block-mount ca-bundle default-settings-chn dnsmasq-full dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-nf-nathelper kmod-nft-offload libc libgcc libustream-openssl logd luci mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-openssl

Installation notes

  • First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
  • Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
  • The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
  • Verify your download against the published checksum before flashing:
    $ sha256sum openwrt-25.12.5-ath79-tiny-sitecom_wlr-7100-squashfs-factory.dlf
    050dca3674af7cab34223bfcfa5a9cfb0c68cb4e4243bfcbde28b9946686da96  openwrt-25.12.5-ath79-tiny-sitecom_wlr-7100-squashfs-factory.dlf

Build custom firmware

Need more than the default image for the Sitecom WLR-7100? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device