Yuncore AX830 OpenWrt Firmware
- CPU
- Qualcomm IPQ5018
- RAM
- 512 MB
- Flash
- 8, 128NAND MB
The Yuncore AX830 is supported by OpenWrt on the qualcommax/ipq50xx target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Qualcomm IPQ5018 |
|---|---|
| CPU cores | 2 |
| CPU frequency | 1000 MHz |
| RAM | 512 MB |
| Flash | 8, 128NAND MB |
| 1 Gbit Ethernet ports | 2 |
| WLAN hardware | Qualcomm IPQ5018 / Qualcomm QCN6122 |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | qualcommax/ipq50xx | yuncore_ax830 |
Downloads
Download images
OpenWrt 25.12.5 · qualcommax/ipq50xx
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-qualcommax-ipq50xx-yuncore_ax830-initramfs-uImage.itb Minimal kernel image, useful for first install or recovery. | kernel | de17ec6f4551… |
| openwrt-25.12.5-qualcommax-ipq50xx-yuncore_ax830-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 2fcba7de5d79… |
| openwrt-25.12.5-qualcommax-ipq50xx-yuncore_ax830-squashfs-factory.ubi For first-time flash from stock firmware. | factory | 518634da8eb4… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Yuncore AX830 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (2)
ath11k-firmware-ipq5018-qcn6122 ipq-wifi-yuncore_ax830
Target default packages (36)
apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-ath11k-ahb kmod-fs-ext4 kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-qca-nss-dp kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-mbedtls logd losetup mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-qualcommax-ipq50xx-yuncore_ax830-initramfs-uImage.itb de17ec6f4551e0b35254f9d7746eebe40b163bfad6f629f3699aba68c22ccc90 openwrt-25.12.5-qualcommax-ipq50xx-yuncore_ax830-initramfs-uImage.itb
Build custom firmware
Need more than the default image for the Yuncore AX830? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Yuncore devices
- Yuncore AX850 OpenWrt firmware
- Yuncore AX880 OpenWrt firmware
- Yuncore CPE200 OpenWrt firmware
- Yuncore FAP650 OpenWrt firmware
- Yuncore M300 OpenWrt firmware
More devices on qualcommax/ipq50xx
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.