Linksys MR5500 OpenWrt Firmware
- CPU
- Qualcomm IPQ5018
- RAM
- 512 MB
- Flash
- 256NAND MB
The Linksys MR5500 is supported by OpenWrt on the qualcommax/ipq50xx target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Qualcomm IPQ5018 |
|---|---|
| CPU cores | 2 |
| CPU frequency | 1000 MHz |
| RAM | 512 MB |
| Flash | 256NAND MB |
| 1 Gbit Ethernet ports | 5 |
| WLAN hardware | Qualcomm QCN5018, Qualcomm QCN9024 |
| Switch | Qualcomm Atheros QCA8337 |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | qualcommax/ipq50xx | linksys_mr5500 |
Downloads
Download images
OpenWrt 25.12.5 · qualcommax/ipq50xx
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-qualcommax-ipq50xx-linksys_mr5500-squashfs-sysupgrade.bin Not sure? Pick this if upgrading from OpenWrt. | sysupgrade | 07b0853b21f4… |
| openwrt-25.12.5-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin For first-time flash from stock firmware. | factory | 367b32b0359a… |
| openwrt-25.12.5-qualcommax-ipq50xx-linksys_mr5500-initramfs-uImage.itb Minimal kernel image, useful for first install or recovery. | kernel | c0769b81ee6b… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Linksys MR5500 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (5)
ath11k-firmware-ipq5018 kmod-ath11k-pci ath11k-firmware-qcn9074 ipq-wifi-linksys_mr5500 kmod-usb-ledtrig-usbport
Target default packages (36)
apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-ath11k-ahb kmod-fs-ext4 kmod-gpio-button-hotplug kmod-leds-gpio kmod-nft-offload kmod-qca-nss-dp kmod-usb-dwc3 kmod-usb-dwc3-qcom kmod-usb3 libc libgcc libustream-mbedtls logd losetup mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls
Installation notes
- First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
- Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-qualcommax-ipq50xx-linksys_mr5500-squashfs-sysupgrade.bin 07b0853b21f43f986c55386f0ba9c87bd40f33125bcbefee53882d2c2a3476f0 openwrt-25.12.5-qualcommax-ipq50xx-linksys_mr5500-squashfs-sysupgrade.bin
Build custom firmware
Need more than the default image for the Linksys MR5500? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Linksys devices
- Linksys E1550 v1 OpenWrt firmware
- Linksys E1700 OpenWrt firmware
- Linksys E2500 v1 OpenWrt firmware
- Linksys E2500 v2 OpenWrt firmware
- Linksys E2500 v2.1 OpenWrt firmware
- Linksys E2500 v3 OpenWrt firmware
- Linksys E3000 v1 OpenWrt firmware
- Linksys E3200 v1 OpenWrt firmware
More devices on qualcommax/ipq50xx
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.