Dongwon T&I DW02-412H (64M) OpenWrt Firmware

The Dongwon T&I DW02-412H (64M) is supported by OpenWrt/ImmortalWrt on the ath79/nand target. 6 firmware images are available from the official OpenWrt 25.12.5 and ImmortalWrt 25.12.1 stable releases — download one below, or build a custom OpenWrt image for this device with your own package selection.

Build matrix

Supported firmware versions

DistributionVersionTargetProfile
OpenWrt25.12.5ath79/nanddongwon_dw02-412h-64m
ImmortalWrt25.12.1ath79/nanddongwon_dw02-412h-64m

Downloads

Download images

OpenWrt 25.12.5 · ath79/nand

ImageTypesha256
openwrt-25.12.5-ath79-nand-dongwon_dw02-412h-64m-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade6de68d4900f3
openwrt-25.12.5-ath79-nand-dongwon_dw02-412h-64m-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kerneld6c46e9b498b
openwrt-25.12.5-ath79-nand-dongwon_dw02-412h-64m-squashfs-factory.img

For first-time flash from stock firmware.

factory4b73474b3057

ImmortalWrt 25.12.1 · ath79/nand

ImageTypesha256
immortalwrt-25.12.1-ath79-nand-dongwon_dw02-412h-64m-initramfs-kernel.bin

Minimal kernel image, useful for first install or recovery.

kernelce8eab751a66
immortalwrt-25.12.1-ath79-nand-dongwon_dw02-412h-64m-squashfs-factory.img

For first-time flash from stock firmware.

factoryaa4badefed66
immortalwrt-25.12.1-ath79-nand-dongwon_dw02-412h-64m-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgradebe00b49ff5c0

Downloads are served by the official OpenWrt/ImmortalWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the Dongwon T&I DW02-412H (64M) ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

OpenWrt 25.12.5 · ath79/nand

Device packages (3)

kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct

Target default packages (29)

apk-mbedtls base-files ca-bundle dnsmasq dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-nft-offload libc libgcc libustream-mbedtls logd mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-basic-mbedtls

ImmortalWrt 25.12.1 · ath79/nand

Device packages (3)

kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct

Target default packages (33)

apk-openssl base-files block-mount ca-bundle default-settings-chn dnsmasq-full dropbear firewall4 fstools kmod-ath9k kmod-gpio-button-hotplug kmod-nf-nathelper kmod-nft-offload libc libgcc libustream-openssl logd luci mtd netifd nftables odhcp6c odhcpd-ipv6only ppp ppp-mod-pppoe procd-ujail swconfig uboot-envtools uci uclient-fetch urandom-seed urngd wpad-openssl

Installation notes

  • First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
  • Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
  • The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
  • Verify your download against the published checksum before flashing:
    $ sha256sum openwrt-25.12.5-ath79-nand-dongwon_dw02-412h-64m-squashfs-sysupgrade.bin
    6de68d4900f37c3b87cc060930edbef14b41b506ab954f2db171da879a98b3d3  openwrt-25.12.5-ath79-nand-dongwon_dw02-412h-64m-squashfs-sysupgrade.bin

Build custom firmware

Need more than the default image for the Dongwon T&I DW02-412H (64M)? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device