Xunlong Orange Pi Plus OpenWrt Firmware
- CPU
- Allwinner H3
- RAM
- 1024 MB
- Flash
- 8192, microSDHC MB
The Xunlong Orange Pi Plus is supported by OpenWrt on the sunxi/cortexa7 target. 3 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.
Specs
Specifications
| CPU | Allwinner H3 |
|---|---|
| CPU cores | 4 |
| CPU frequency | 1600 MHz |
| RAM | 1024 MB |
| Flash | 8192, microSDHC MB |
| 1 Gbit Ethernet ports | 1 |
| WLAN hardware | Realtek RTL8189ETV |
Hardware data from the OpenWrt Table of Hardware; verify against your unit before flashing.
Build matrix
Supported firmware versions
| Distribution | Version | Target | Profile |
|---|---|---|---|
| OpenWrt | 25.12.5 | sunxi/cortexa7 | xunlong_orangepi-plus |
Downloads
Download images
OpenWrt 25.12.5 · sunxi/cortexa7
| Image | Type | sha256 |
|---|---|---|
| openwrt-25.12.5-sunxi-cortexa7-xunlong_orangepi-plus-squashfs-sdcard.img.gz Disk image to write onto an SD card. | sdcard | ca94b60da40d… |
| openwrt-25.12.5-sunxi-cortexa7-xunlong_orangepi-plus-ext4-sdcard.img.gz Disk image to write onto an SD card. | sdcard | fdabdf5a508b… |
| openwrt-25.12.5-sunxi-cortexa7-xunlong_orangepi-plus-initramfs-kernel.bin Minimal kernel image, useful for first install or recovery. | kernel | 2f7002b393ec… |
Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.
Packages & install
Default packages & installation
Default packages
Every image for the Xunlong Orange Pi Plus ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.
Device packages (1)
kmod-rtc-sunxi
Target default packages (28)
apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs firewall4 fstools kmod-nft-offload libc libgcc libustream-mbedtls logd mkf2fs mtd netifd nftables odhcp6c odhcpd-ipv6only partx-utils ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd
Installation notes
- The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
- Verify your download against the published checksum before flashing:
$ sha256sum openwrt-25.12.5-sunxi-cortexa7-xunlong_orangepi-plus-squashfs-sdcard.img.gz ca94b60da40d658782cecffa98b854e00d02e9bf96b259591a382c59ec2d6ff5 openwrt-25.12.5-sunxi-cortexa7-xunlong_orangepi-plus-squashfs-sdcard.img.gz
Build custom firmware
Need more than the default image for the Xunlong Orange Pi Plus? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.
Customize firmware for this deviceRelated
Related devices
More Xunlong devices
- Xunlong Orange Pi 2 OpenWrt firmware
- Xunlong Orange Pi One OpenWrt firmware
- Xunlong Orange Pi One Plus OpenWrt firmware
- Xunlong Orange Pi PC OpenWrt firmware
- Xunlong Orange Pi PC 2 OpenWrt firmware
- Xunlong Orange Pi PC Plus OpenWrt firmware
- Xunlong Orange Pi R1 OpenWrt firmware
- Xunlong Orange Pi R1 Plus OpenWrt firmware
More devices on sunxi/cortexa7
- Cubietech Cubieboard2 OpenWrt firmware
- Cubietech Cubietruck OpenWrt firmware
- FriendlyARM NanoPi M1 Plus OpenWrt firmware
- FriendlyARM NanoPi NEO OpenWrt firmware
- FriendlyARM NanoPi NEO Air OpenWrt firmware
- FriendlyARM NanoPi R1 OpenWrt firmware
- FriendlyARM ZeroPi OpenWrt firmware
- Lamobo Lamobo R1 OpenWrt firmware
Upstream
Upstream & source
Images are assembled from packages compiled and published by the upstream OpenWrt and ImmortalWrt projects. The complete corresponding source code is available from those projects under the GPL.