MikroTik RB5009 OpenWrt Firmware

The MikroTik RB5009 is supported by OpenWrt on the mvebu/cortexa72 target. 6 firmware images are available from the official OpenWrt 25.12.5 stable release — download one below, or build a custom OpenWrt image for this device with your own package selection.

Build matrix

Supported firmware versions

DistributionVersionTargetProfile
OpenWrt25.12.5mvebu/cortexa72mikrotik_rb5009

Downloads

Download images

OpenWrt 25.12.5 · mvebu/cortexa72

ImageTypesha256
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-ext4-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade7c442b53e792
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-initramfs-uImage.itb

Minimal kernel image, useful for first install or recovery.

kernelf1bb5619b56b
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-squashfs-sysupgrade.bin

Not sure? Pick this if upgrading from OpenWrt.

sysupgrade53ffdebc038b
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-squashfs-factory.ubi

For first-time flash from stock firmware.

factoryb01158da9077
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-ext4-factory.ubi

For first-time flash from stock firmware.

factory027c54f5ac06
openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-targz-rootfs.tar.gz

Rootfs archive for Docker / LXC containers.

rootfs26991a3ddac9

Downloads are served by the official OpenWrt mirrors — unchanged upstream stable builds.

Packages & install

Default packages & installation

Default packages

Every image for the MikroTik RB5009 ships these packages by default. The customize option below lets you add or remove packages before the image is assembled.

Device packages (3)

kmod-i2c-gpio yafut kmod-dsa-mv88e6xxx

Target default packages (30)

apk-mbedtls base-files ca-bundle dnsmasq dropbear e2fsprogs ethtool firewall4 fstools kmod-gpio-button-hotplug kmod-nft-offload libc libgcc libustream-mbedtls logd mkf2fs mtd netifd nftables odhcp6c odhcpd-ipv6only partx-utils ppp ppp-mod-pppoe procd-ujail uboot-envtools uci uclient-fetch urandom-seed urngd

Installation notes

  • First install from stock firmware: flash the factoryimage through the vendor firmware's upgrade page or recovery mode.
  • Already running OpenWrt or ImmortalWrt: flash the sysupgrade image from LuCI (System → Backup / Flash Firmware) or with the sysupgrade command.
  • The kernel / initramfs image boots from RAM without writing to flash — useful for a first install or for recovering from a failed flash.
  • Verify your download against the published checksum before flashing:
    $ sha256sum openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-ext4-sysupgrade.bin
    7c442b53e7923205b7441ef0b450f6de4a1513c66b9862eac70b4232686ffd55  openwrt-25.12.5-mvebu-cortexa72-mikrotik_rb5009-ext4-sysupgrade.bin

Build custom firmware

Need more than the default image for the MikroTik RB5009? Pick your packages — LuCI apps, themes, VPN clients — set the basics, and get a ready-to-flash OpenWrt image assembled from official packages in minutes.

Customize firmware for this device